For remotely triggering Canon cameras equipped with an N3 remote shutter release terminal and controlling half-press function using certain PocketWizard radios.
Cable lengths: 3' (91.5 cm) and 1' (30 cm)
From: 1/8" (3.5 mm) stereo miniphone
To: Canon N3 remote terminal
• PlusX (trigger only)
• Plus III
• MultiMAX with -ACC port
• For the Plus II, older MultiMAX, or other PocketWizard radios, we recommend using a CM-N3-P or CM-N3.
Description: This is a special remote shutter release cable called a Pre-Trigger cable. A pre-trigger cable controls both the half-press and full-press function of your remote camera’s shutter release. When a camera is “pre-triggered”, it is like holding your camera’s shutter release button in the half-pressed or metering/focusing position.
This –ACC cable allows a compatible PocketWizard radio to independently control both half-press and full-press functions.
A Standard Cable works with most PocketWizard radios but has no half-press control, and is for basic remote triggering only. (Using a CM-N3-ACC cable with a MSMM Adapter will provide the same function as a CM-N3 cable.)
A -P Cable works with most PocketWizard radios. This pre-trigger cable has a switch that allows you to toggle half-press on or off at the remote camera's position, but not from the transmitting radio. (Using a CM-N3-ACC cable with a PTMM Adapter will provide the same function as a CM-N3-P cable.)
Compatible with the following radios:
PlusX: Use this cable with the PlusX to trigger the camera.
Plus III: Use this cable with the Plus III’s exclusive 2-stage trigger to wake-up or focus your remote camera just like using the camera’s shutter release button.
Plus II or MultiMAX with no -ACC port: Use the MSMM adapter with this CM-N3-ACC cable or use the CM-N3.
MultiMAX with –ACC port: Enable a remote zone with your hand-held MultiMAX, and your remote MultiMAX will wake up its remote camera with this cable. As long as the zone is turned on, the remote camera will stay awake and respond more quickly and consistently, but also consume the camera's batteries much more quickly. When the remote zone is disabled, the camera will enter its normal sleep modes. The MultiMAX does not support the 2-stage trigger function.
FlexTT5: This cable is required for auto-relay mode with TTL, or other remote triggering with the FlexTT5. Learn more here. You can use a CM-N3-P cable or CM-N3 standard cable with a FlexTT5, but your remote camera will not be able to relay a TTL signal to speedlights. The FlexTT5 does not support the 2-stage trigger function.
Please see our PocketWizard Wiki for more details.
Compatible with cameras using Canon's N3 remote terminal including:
EOS-1D Mark II EOS-1V HS
EOS-1D Mark IIN EOS-3
EOS-1D Mark III EOS 5D
EOS-1D Mark IV
EOS 5D Mark II EOS D30
EOS-1Ds EOS 5D Mark III EOS D60
EOS-1Ds Mark II EOS 6D EOS D2000
EOS-1Ds Mark III EOS 7D
For remotely triggering a flash equipped with a 1/8" (3.5 mm) mono miniphone sync...
The PocketWizard AC7 RF Shield for FlexTT5 solves the problem of limited performance of the...
Locking PC Sync Cable For connecting to a locking/non-locking PC terminal. Cable length: 5' (1.5...
Subscribe to our newsletter and always be the first to hear about what is happening.
|Melbourne||(03) 9672 2222|
|Sydney||(02) 8004 7945|
|Brisbane||(07) 3103 1429|
|Perth||(08) 6102 6382|
|Adelaide||(08) 7200 3773|
|Darwin||(08) 8911 1262|
|Canberra||(02) 6176 0125|
|Hobart||(03) 6107 9442|
|Auckland||(09) 887 0479|
© 2016 michaels camera video digital.