Pre-Trigger Remote Cable
For connecting a PlusX, Plus III, FlexTT5 or MultiMAX with ACC port to a Nikon 10-pin remote shutter release terminal.
Cable lengths: 3' (91.5 cm) and 1' (30 cm
From: 1/8" (3.5 mm) stereo miniphone
To: Nikon 10-pin remote shutter release terminal
• Plus III
• MultiMAX with ACC port to a Nikon 10-pin remote shutter release terminal
•For the Plus II, older MultiMAX or other PocketWizard radios, Please use a N90M3 or a N90M3-P cable.
Description: This is a special remote shutter release cable called a Pre-Trigger Cable. A Pre-Trigger cable controls both the half-press and full-press function of your remote camera’s shutter release. When a camera is “pre-triggered”, it is like holding your camera’s shutter release button in the half-pressed or metering/focusing position.
This cable contains a "no diode" circuit necessary only for the newer Nikon cameras, but will work with other cameras as listed below. It will not work with the Nikon D200 or D100 w/ MB-D100. Use the N10-ACC-D200 (formerly the N90M-ACC) cable for those cameras.
This N10-ACC (formally the N90M-ACC-ND) cable allows a compatible PocketWizard radio to independently control both half-press and full-press functions.
Compatible with the following radios:
PlusX: Use this cable with the PlusX to trigger the camera.
Plus III: Use this cable with the Plus III’s exclusive 2-stage trigger to wake-up or focus your remote camera just like using the camera’s shutter release button.
FlexTT5: This cable is required for auto-relay mode with E-TTL, or other remote triggering with the FlexTT5. Learn more here. You can use a N90M3–P (-P) Pre-Trigger cable or N90M3 standard cable with a FlexTT5, but your remote camera will not be able to relay an E-TTL signal to Speedlites. The FlexTT5 does not support the 2-stage trigger function.
MultiMAX with –ACC port: Enable a remote zone with your hand-held MultiMAX, and your remote MultiMAX will wake up its remote camera with this cable. As long as the zone is turned on, the remote camera will stay awake and respond more quickly and consistently, but also consume the camera's batteries much more quickly. When the remote zone is disabled, the camera will enter its normal sleep modes. The MultiMAX does not support the 2-stage trigger function.
NOTE: An older mono motor drive cable and/or pre-release cable can be used instead of an -ACC cable with a FlexTT5 but you will not have E-TTL capability.
Please see our PocketWizard Wiki for more details.
Compatible with cameras using Nikon's 10-pin remote terminal including:
DCS Pro SLR/n S3 Pro
D3s DCS Pro 14n
S3 Pro UV IS
D4s DCS 660
D300 DCS 660M
For remotely triggering a flash equipped with a 1/8" (3.5 mm) mono miniphone sync...
The PocketWizard AC7 RF Shield for FlexTT5 solves the problem of limited performance of the...
Locking PC Sync Cable For connecting to a locking/non-locking PC terminal. Cable length: 5' (1.5...
Subscribe to our newsletter and always be the first to hear about what is happening.
|Melbourne||(03) 9672 2222|
|Sydney||(02) 8004 7945|
|Brisbane||(07) 3103 1429|
|Perth||(08) 6102 6382|
|Adelaide||(08) 7200 3773|
|Darwin||(08) 8911 1262|
|Canberra||(02) 6176 0125|
|Hobart||(03) 6107 9442|
|Auckland||(09) 887 0479|
© 2016 michaels camera video digital.